WATTYL PAINT CORP -- ACRYLIC LATEX LINE TRAFFIC PAINT, 65-810  -- 8010-00N070595
<pre>=====================  Product Identification  =====================

Product ID:ACRYLIC LATEX LINE TRAFFIC PAINT, 65-810
MSDS Date:08/13/1992
FSC:8010
NIIN:00N070595
=== Responsible Party ===
Company Name:WATTYL PAINT CORP
Address:5275 PEACHTREE INDUSTRIAL BLVD
City:ATLANTA
State:GA
ZIP:30341
Country:US
Info Phone Num:404-455-7000
Emergency Phone Num:800-424-9300 (CHEMTREC)
CAGE:WATTL
=== Contractor Identification ===
Company Name:WATTYL PAINT CORP
Address:5275 PEACHTREE INDUSTRIAL BLVD
City:ATLANTA
State:GA
ZIP:30341
Country:US
Phone:404-455-7000
CAGE:WATTL

=============  Composition/Information on Ingredients  =============

Ingred Name:NON-HAZARDOUS INGREDIENTS
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:MAY CONTAIN MATERIALS SUCH AS INGS 3-6
RTECS #:9999999ZZ
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:SILICA
CAS:60676-50-0
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:TALC (POWDER), CONTAINING NO ASBESTOS FIBERS; (TALC)
CAS:14807-96-6
RTECS #:WW2710000
OSHA PEL:20 MPPCF
ACGIH TLV:2 MG/M3 RDUST

Ingred Name:CALCIUM CARBONATE
CAS:1317-65-3
RTECS #:EV9580000
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST

Ingred Name:TITANIUM OXIDE; (TITANIUM DIOXIDE)
CAS:13463-67-7
RTECS #:XR2275000
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:YES
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:ACUTE: INHALATION: WITH POOR
    VENTILATION, VAPOR OR SPRAY MIST MAY IRRITATE RESPIRATORY MUCOUS
    MEMBRANES, CAUSING HEADACHE AND NAUSEA. EYE CONTACT: PRIMARY
    IRRITANT. CHRONIC: NONE RECOGNIZED.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

=======================  First Aid Measures  =======================

First Aid:INHAL: REMOVE TO FRESH AIR. EYES: FLUSH IMMEDIATELY WITH
    LARGE AMOUNTS OF WATER FOR AT LEAST 15 MINUTES. TAKE TO MD FOR
    MEDICAL TREATMENT. SKIN: REMOVE WITH SOAP AND WATER. IF DRENCHED,
    REMOVE CONTAMI NATED CLOTHING. INGEST: IF CONSCIOUS, GIVE 2 GLASSES
    OF WATER TO DILUTE. DO NOT INDUCE VOMITING. CONSULT MD OR POISON
    CONTROL CENTER.

=====================  Fire Fighting Measures  =====================

Flash Point:NONE
Lower Limits:NONE
Extinguishing Media:WATER FOG (APPLICABLE ONLY FOR COOLING CLOSED
    CONTAINERS).
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA AND FULL
    PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE WHEN
    EXPOSED TO EXTREME HEAT.

==================  Accidental Release Measures  ==================

Spill Release Procedures:VENTILATE AS DESCRIBED. AVOID UNNECESSARY SKIN
    CONTACT. COLLECT BY ABSORPTION, SHOVEL AND/OR WET MOPPING.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:DO NOT STORE ABOVE 120F. CLOSED
    CONTAINER AFTER EACH USE.
Other Precautions:PIGMENTED PAINTS & COATINGS (THOSE WHICH ARE OPAQUE,
    COLORED OR WHICH HAVE REDUCED GLOSS WHEN DRY) MAY CNTN MATLS SUCH
    AS SILICA, TALC, CALCIUM CARBONATE, TITANIUM DIOXIDE, ETC WHICH ARE
    HAZ TO INHALE  IN DRY PWDR FORM. THESE (SUPDAT)

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:DURING SPRAY APPLICATION USE NIOSH/MSHA APPROVED
    MECHANICAL FILTER RESPIRATOR TO REMOVE SOLID AIRBORNE PARTICLES OF
    OVERSPRAY.
Ventilation:PROVIDE SUFFICIENT VENTILATION IN VOLUME & PATTERN TO
    INSURE VAP CONCS WELL BELOW ANY TLV & LEL LISTED IN INGREDIENTS.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGLES .
Other Protective Equipment:ANSI APPROVED EYE WASH & DELUGE SHOWER .
Work Hygienic Practices:DO NOT TAKE INTERNALLY. OBSERVE GOOD SANITARY
    PRACTICES.
Supplemental Safety and Health
OTHER PRECS: HAZS ARE NOT BELIEVED TO BE PRESENT WHEN PWDRS ARE
    DISPERSED IN LIQ COATINGS. HOWEVER, PRECS GIVEN IN SPECIAL PROT
    INFO SECTION SHOULD BE CAREFULLY OBSERVED & NIOSH/MSHA APPRVD RESPS
    SHOU LD ALSO BE USED IF DRIED COATING IS SANDED/ABRADED IN SUCH A
    WAY AS TO PRODUCE DUST.

==================  Physical/Chemical Properties  ==================

Boiling Pt:B.P. Text:212F,100C
Vapor Density:LTR/AIR
Spec Gravity:1.402 
Evaporation Rate &amp; Reference:SLOWER THAN ETHER
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.
Percent Volatiles by Volume:70

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
NONE KNOWN.
Stability Condition to Avoid:HIGH TEMPERATURES.
Hazardous Decomposition Products:WHEN HEATED TO DECOMPOSITION, AS IN A
    FIRE OR IN WELDING, MAY PRODUCE TOXIC FUMES SUCH AS CARBON MONOXIDE
    .

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSE IN ACCORDANCE WITH LOCAL, STATE AND
    FEDERAL REGULATIONS. DO NOT INCINERATE CLOSED CONTAINERS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.